flash - Yongnuo YN-568EX (for Nikon)
I successfully learned the profile and things were working as advertised but I then had a problem with the flash and sent it back under warranty.
When my replacement flash arrived the learned profile no longer worked. So I went through the learning process again, and it was successful. Even though the learning worked I am unable to change power output. For reference with the flash in manual without the V6 it looks like its firing at about 1/16 power.
Any idea why it wouldn't work this time around with the same model flash? Why learning would be successful but not be able to change power?
Any help would be appreciated, thank you in advance.
I'm surprised to hear that you were able to create a flash profile for it since that would mean the flash supports analogue TTL (used for film cameras).
Do you actually see the speedlight emit flashes with different power levels during profiling?
I noticed that the latest firmware version for the V6 made changes to the profiling (making it slower). If you are using that and it has worked before for you, perhaps try to go back to an earlier firmware and see whether the profiling works again.
That depends what Yongnuo did to your flash when they serviced it for you.
Maybe they swapped a new firmware for you and made it no longer compatible fot profiling? Say it used to have an analogue TTL mode but after they serviced it, the flash only has digital TTL so you could no longer learn it using the Flash Learning Program.
If it's now runs solely on digital TTL, try choosing Nikon SB-700's profile and see if it works on your YN-568EX.
Good luck !
About the D750 hot shoe problem, I found an article on Peta Pixel with pictures, have a look. In short, it's out of spec - different from any other Nikon cameras.
If you switched to the D750, the only option is for you to send your V6 units to us and we will swap the special hot shoe for you. More info here on returning your units.
If that worked well then it would have the advantage of fixing the connection issues the D750 can have with other equipment, including some Nikon flashes.
The current D750 special shoe is still compatible with most other camera systems but it's not perfect on the D750 as we wanted it to be as there will always be limitations if we want to go multi-brand. We are considering if we should take a step further and make a second generation of the special shoe, but this time a dedicate version just for the D750. This way we can take out any wiggle / contact issues. I'll keep you all posted if this really happens!
I don't think the Nikon version of Yongnuo flashes are supported. Too bad we don't have it in the studio to test it for you.
Anyone on the forum has one to try?
You can control power as well as zoom
on the RF60, charge 2 less AA batteries, and carry less in your bag.
you have an extra V6 that you may even use it as hand remote and use
the Relay Mode of the V6.
if you mostly use this new flash as an on-camera fill flash (with TTL) and only sometimes put it off-camera, then that's another story. It's only if you are looking for a flash mostly for off-camera use then RF60 would be a sensible option
If the RF60 can do that I will buy two right away.
Nikon system models:
- Cactus AF45N, AF50N;
- Godox V860N;
- Metz 36AF-5, 44AF-1, 50AF-1, 58AF-2;
- Nikon SB-24, SB-28, SB-600, SB-700, SB-800, SB-900, SB-910;
- Nissin Di700;
- Sigma EF-530 DG SUPER;
In general, there are also those Nikon-compatible models which were confirmed to be compatible for profiling with the V6, i.e., it is possible to create a profile for them (through a simple procedure).
However, again, some of those models may not support "i-TTL" but only "TTL" (which modern DSLRs cannot exploit anymore).
@MichelSauret please take note - choose a flash that has i-TTL.
Thank you for your attention.